Litronic FMS RMH12 pipe sensor

The Liebherr in situ water content determination Litronic-FMS III-RMH12 is used to detect the water content (concentration determination) even in very low ppm ranges in emulsions such as diesel fuel, transmission, hydraulic, engine, roller bearing, transformer and turbine oil as well as in battery systems.

The sensors were developed in cooperation with the ISO/TS 16332 standardisation committee for the water separation ability of diesel fuel filters.

The installation takes place on test and inspection stands and replaces the previous manual sampling as well as other offline measuring systems.

Measurement by the Liebherr sensor system is based on the physical principle of capacitance determination in the high-frequency stray field.

In addition to their high precision and robustness, the measuring devices from Bad Schussenried are characterised by their reproducibility.

Once the system has been calibrated, further measuring points can be set up or devices renewed on this basis at any time without great effort. The plant thus always remains reliable, regardless of its previous term and age.

Physical principle	Coaxial field in a cylinder condenser
Frequency	20 MHz
Measurement location	Pipe diameter 12 mm
Process connection	Ermeto cutting ring screw connection 12 mm, M18x1.5
Measuring range	0 – 100 % water content, measuring window adjustable
Capacity resolution	250 aF
Update cycle	33.33 ms
Maximum attainable measuring accuracy	+/- 10 ppm water content 1.)
Measurement value transfer	digital: RS-485, streaming
Max. number of sensors on the bus	4
Maximum bus length	1200 m
Power supply	12-24 V, 0.5 VA
Temperature measurement measuring range	5 – 90 °C
Operating ambient temperature	5 – 60 °C
Storage temperature	-40 – 60 °C 2.)
Protection class	IP65
Max. pressure	6 bar
Volume flow	5 - 1200 l/h
Connection line length/type	UNITRONIC® ROBUST C 7x0.14 shielded/6 m
Housing material	V4A (1.4305)
Dimensions: Ø/Length	54/219 (230) mm
Weight without cable	approx. 2.1 kg

1.) with ideal flow behaviour and proper calibration

2.) free of liquid

Characteristics

• Direct digital measuring process.

• Extremely high capacity resolution due to patented measuring circuit

• 30 measurements per second enable assessment of the dynamic behaviour

• Automatic reference equalisation every second

• Temperature-stabilised, regulated quartz time base (TCXO)

• High-resolution temperature measurement/compensation of the liquid.

• High-resolution temperature measurement/compensation of the measuring circuit.

• Extremely high water resolution due to optimum geometry of the coaxial condenser.

• Ceramic coaxial condenser.

• High quality stainless steel housing.

• Resistant against aggressive liquids/oils.

• Flow-optimised throughput with even cross-section.

• Simple process connection.

• Digital interface/networking.

• Data-streaming technology with automatic bus arbitration.

Indirect measuring method: Capacity determination in the high frequency stray field. This method uses the different dielectric constant (permittivity) of water and liquids.
Fully reproducible sensors: If the plant is subsequently extended with sensors or if sensors are replaced, no recalibration is necessary thanks to the built-in microprocessor.
Process control and regulation: Thanks to extensive interfaces, the moisture measurement can be integrated into process control systems and controls.
Cost saving: Time-consuming and costly laboratory analyses are no longer necessary or can be reduced.
Temperature measurement/temperature compensation: The sensor can also be used to determine the temperature of the medium.
Limit values: Maximum or minimum limits can be set using the software. Light or sound signals can be triggered if required.
Mean value calculator: The sensor passes on already averaged values to the FMS evaluation and transfer module.
Material flow: The entire liquid is measured (coaxial capacitor).
Rapid reaction time: The sensor measures 30 times a second and passes on already averaged values to the evaluation unit.
Measurement accuracy: Stable, extremely high measurement resolutions of up to 3 ppm are possible.
High-quality materials: The use of high-quality materials is also reflected in the resistance to a wide range of oils.
Software and evaluation and transfer module: The mandatory software integrated in the Litronic-FMS evaluation and transfer unit is used for recording, processing and preparing the values measured by the sensors, parametrisation and calibration. In addition, the unit offers graphic visualisation and further signal transfer to higher-level controls.

rmh animation D-E

Sales contact person

Liebherr-Mischtechnik GmbH

Im Elchgrund 12
88427 Bad Schussenried
Germany

+49 7583 9498-07

Service contact person

Liebherr-Mischtechnik GmbH

Im Elchgrund 12
88427 Bad Schussenried
Germany

+49 7583 9498-00