06/13/2016 Liebherr 1000 EC-B 125 Litronic tower crane used for the first time to erect a wind turbine with a hub height of 149m

  • 1000 EC-B erects wind turbine with a hub height of 149 m
  • Tower crane reaches a final hook height of 164 m
  • Space-saving assembly on a small hilltop in the middle of the Black Forest

A Liebherr tower crane recently erected a wind turbine at an altitude of around 800m in the Prechtaler Schanze Wind Farm in the Black Forest. The 1000 EC-B with its extremely low footprint erected for the first time a wind turbine with a hub height of 149m on the hills between the towns of Gutach and Mühlenbach. The tower crane had never before been assembled to such a height for wind turbine manufacturer ENERCON – both with and without guying to the wind turbine tower.

The Liebherr 1000 EC-B 125 Litronic tower crane erecting the ENERCON wind turbine.

The Liebherr 1000 EC-B 125 Litronic tower crane erecting the ENERCON wind turbine.

ENERCON's Liebherr 1000 EC-B 125 Litronic tower crane erected a new wind turbine in the Prechtaler Schanze Wind Farm in April 2016. With a hub height of 149 m and a blade diameter of 115m, it is the largest turbine ever to be erected using this crane. With its 31.50m jib and a hook height of 164m, the crane was still able to hoist 100t using four lines – one of the main features of the most powerful Flat-Top crane built by Liebherr which has been enhanced for erecting wind turbines. The maximum load capacity of this crane is 125t in the six-line version or 100t in the four-line version.

Logistic benefits for transport and erection at remote sites

Wind turbines in areas with poor wind conditions are not generally used in large wind farms and instead are erected in wooded areas or locations with difficult access. Both these criteria are applied to this site in the southern Black Forest. According to ENERCON, only the 1000 EC-B 125 Litronic could be considered for the small, steep hilltop in Gutach, Mühlenbach in the middle of the forest. The area required for erecting a complete Flat-Top crane is approximately half of the normal standing area of other crane systems. The jib used in this case was very short which is why no additional site clearance work was required for its assembly.

In addition the logistics required to transport the 1000 EC-B 125 Litronic are much less than for comparable crane systems since the various components of the tower crane are supplied in small packages. The jib components of the large crane can be inserted into the tower elements, transported on a truck and assembled on site.

The Liebherr Flat-Top crane has a very small footprint.

The Liebherr Flat-Top crane has a very small footprint.

1000 EC-B 125 Litronic Flat-Top crane from ENERCON climbs to record height

First of all the compact Liebherr LR 1200 crawler crane assembled the Flat-Top crane to its initial hook height of 39 m. From this point the tower crane erected the wind turbine and was able to climb up the turbine tower as it rose using its own climbing equipment.

For this job in the southern Black Forest it climbed to a free-standing hook height of 110m. It was guyed to the wind turbine at a height of 100m. Using this single guying, the crane climbed to a final hook height of 164 m. Both free-standing and also fully climbed and guyed, these represented hook heights that ENERCON had never achieved before. They were only possible because Liebherr's flagship Flat-Top crane was assembled on the 1000 HC tower system. The monoblock tower sections with system dimensions of 3.40m x 3.40m and a length of 5.80m allow high free-standing erection heights with short erection times. The erection of the wind turbine took around four weeks.

In addition the crane was fitted with an adjustable undercarriage with a support base measuring 18.0 x 18.0m at the request of ENERCON for the erection of the first turbine. The support arms can be adjusted on this special undercarriage from the 45° position by +/- 5° or +/- 10°. The footprint of the support base is then 20.4m x 15.2m. This means that the crane can be moved closer to the object since it requires so little space.

Specialist for wind turbine erection

The locations chosen for wind turbines generally have harsh wind conditions which can adversely affect cranes. One specific benefit of tower cranes is their operational safety in wind speeds of up to 65 km/h.

The infinitely adjustable crane drive units also allow high working speeds to be used. MICROMOVE fine positioning mode enables the concrete rings, nacelles and rotor blades to be positioned and set down with millimetre precision. The very long rotor blades can also be positioned with millimetre accuracy since swinging movements of the attached components are prevented.

The crane driver has a perfect view of what is going on from the cabin. This makes it easier to position the rotor blades precisely and safely using the trolley jib.

Downloads

Contact person

Hans-Martin Frech

Marketing & Market Management

Liebherr-Werk Biberach GmbH

Memminger Straße 120

88400 Biberach an der Riß

Germany

  • Phone+49 7351 41-2330
  • Fax+49 7351 41-2223

Video

ENERCON's Liebherr 1000 EC-B 125 Litronic tower crane erected a new wind turbine in the Prechtaler Schanze Wind Farm in April 2016. With a hub height of 149m and a blade diameter of 115m, it is the largest turbine ever to be erected using this crane.

Liebherr 1000 EC-B 125 Litronic in the Prechtaler Schanze Wind Farm in the Black Forest. Watch video

ENERCON's Liebherr 1000 EC-B 125 Litronic tower crane erected a new wind turbine in the Prechtaler Schanze Wind Farm in April 2016. With a hub height of 149m and a blade diameter of 115m, it is the largest turbine ever to be erected using this crane.